Import Two or More Survey Files to Reach Minimum Area

Question:  
Is it possible to merge two or more fields just for import in order to have at least 15ha to import? 

Answer:  
You can import multiple field surveys into one osd file to get the total area above 15ha (eg 6 + 8 + 8 = 22ha).  Then define the boundary to design one field (say 6ha) and then export.  You will then be asked to pay for the total survey area (22ha).  Proceed and pay for the full area. Save the osd file, then 'Save As' another osd filename and then adjust the boundary to another field (next 8ha) and design.

When you export again you will not be asked to pay again. Note the fields should be within a few miles of each other so the OSD file is not too spread out.  Go to Tools > Import then select the survey file. Import each of the survey files to the same osd file creating one combined field.


Tips and Tricks

  1. Water Control Structures
  2. Smoothing Distance
  3. Erosion Control Banks & Waterway
  4. Drainage Design Solutions of Different Topographies
  5. Runoff vs Slope
  6. Trimble Field Level II Do Not Show the .gps File
  7. Minimum Recommended Smoothing Distance For Export To Trimble Field Level 2
  8. GPS Base Station Setup For Best Vertical Accuracy
  9. How to Survey with Trimble FMX
  10. How Easy is OptiSurface to Use for the Average Farmer?
  11. Balancing Earthworks in the Field
  12. Landform Design Slopes and Smoothing
  13. Export Proposed Topography to AutoCAD
  14. Surface Irrigation Designs with Variable Slope
  15. OptiSurface Designer Import and Export Format
  16. Importing Multiple Survey Files to OSD
  17. Can Drone Or LIDAR Surveys be used with OptiSurface?
  18. Calculation Grid Spacing and Export Grid Spacing
  19. How to Survey a Field for Landforming Design
  20. Loading .gps File in FMX
  21. Designing a Field in Sections
  22. Using an Old OSD File versus a New Survey
  23. No Master Benchmark on Imported Survey File
  24. Displaying Secondary Benchmarks
  25. Import Error for xyz File Due to Encoding Format
  26. OptiSurface4D: Bounded By Ridges
  27. Can OptiSurface handle curved rows in Drainage Analysis & Runoff Analysis?
  28. Reverse Grades to Main Slope
  29. Measuring Culvert Invert Level
  30. Surveying a 1000-Ha Field
  31. GPS Coordinate System Check
  32. Does A Normal UTM Zone Coordinate Need To Be Trimmed To x Digits?
  33. Can You Import Data Directly From GPS System?
  34. Converting Latitude/Longitude to Easting/Northing
  35. Surveying With Any GPS Equipment and Exporting to a gps file for the Trimble FMX
  36. DGPS Post Treating System with 5cm Precision For Landforming
  37. Exporting to Trimble FMX Field Level
  38. Can I Survey with a GPS System on an ATV?
  39. Standard NMEA GPGGA txt File to Import into OptiSurface Designer
  40. 900 Acres: Cut that large survey down.
  41. Export Options for Data Layers
  42. Import Two or More Survey Files to Reach Minimum Area
  43. Different Row Slope Directions In One Field
  44. Does OptiSurface allow for multiple grade breaks per design, taildrains roads, pads etc?
  45. Can I View DTM/Topography In Plan View Or 3D Type View When Doing A Design?
  46. Adjust the Bands in the Legend
  47. Design for a 1000-Ha Field
  48. Would It Be Possible That The Numbers In The Boundary Zone Appear In The New Subzone Created?
  49. Grade Of Best Fit And Splitting The Field Into Boundaries
  50. Acceptable Minimum Slopes
  51. Incorrect Area in OptiSurface
  52. Valley Subzone Not Behaving as Expected
  53. Difference Between Breaklines And Subzones
  54. Alignment of Furrow/Bed Direction with OptiSurface Design Mainslope Direction
  55. Subzones Settings Over Ride Boundary Zone Settings
  56. Printing the Maps
  57. Print Size

Feedback and Knowledge Base